Cookie Img
Send Inquiry Send SMS    Call Me Free Offline
Home » Products » Acrylic Base Waterproofing Paint For Terrace And Roof » Acrylic Base Waterproofing Paint For Terrace And Roof

Acrylic Base Waterproofing Paint For Terrace And Roof

Acrylic Base Waterproofing Paint For Terrace And Roof
Acrylic Base Waterproofing Paint For Terrace And Roof
Product Code : 01
Product Description

Acrylic Base Waterproofing Paint For Terrace And Roof

Product Description:

Sealer Coat (Acrylic Based Waterproofing Paint) is an elastomeric, flexible single pack waterproofing membrane made out of 100% pure acrylic polymers under the technical collaboration of M/s Insulating Paints Inc Australia. It is used to fill Hair line cracks on walls and terrace. It's gives a smooth and sheen finish to all surfaces. It has been tested by G.E.R.I. Vadodara & National Test House Calcutta.

Features:

  • Gives a smoother and transparent surface to the floor
  • Offers good abrasion resistance

Advantages:

  • Gives excellent waterproofing.
  • It is washable and Scrub resistant.
  • It eliminates the requirement of any other primer coat.
  • Excellent resistance to algae and fungus.
  • Being elastic in nature it allows minor structural movements.

Coverage Area:

  • On Smooth Surface,1Kg Sealercoat Covers Approximately 20 sqft in 2 coats.

Applied
:
  • It can be apply for Galvanize/ Asbestos Sheet and also for R.C.C & Cement Surfaces.

Application Method:

For R.C.C. & Cement surfaces & Asbestos sheet:-
  • Surface Preparation:-Clean the surface with adequate quantity of water. Make surface dust & grease free; remove all previous coatings which may have loose bond with the surface. If required, scrub with wire brush or use scrapper to remove old flake, chips & dust.
  • Filling of Cracks :-Weather cracks are the cause of water/leakages thru wall and roofs of buildings. In case of a presence of prominent surface cracks please fill up the cracks with Diamond shield or any good quality crack filler before applying sealercoat
  • Primer Coat:- Old, uneven and highly porous cement surfaces absorb essential polymers of Sealercoat. Hence- apply one or two coats of Sealoxy Primer or any other water based Undercoat for the best results and good finish.
  • Final Finish:-Apply two Coats of Diluted Sealercoat with 15% water & should be applied with an interval of 3 to 4 hours between two coats.

For Any Metal Sheet:

  • Surface Preparation:-Clean the surface and make it dust, grease & Oil free and then apply a coat of good quality zinc phosphate primer to avoid corrosion of the metal sheet.
  • Joint Filling:- Between the overlaying joints of Galv. / Asb. Sheets, insert cotton bedding or gauze, soaked & dipped in un diluted Sealercoat for at least 2 inch in depth. (Length wise). Galvanized ā€œJā€ bolts may be covered with cotton gauze dipped in undiluted Sealercoat & liberally wrapped around the bolt to cover sufficient area.
Additional Information:
  • Minimum Order Quantity: 100 Kilogram(s)

Chitra Insultec Pvt. Ltd.

Contact Us

( *represents compulsory fields )

Tips on getting accurate quotes. Please include product name, order quantity, usage, special requests if any in your inquiry.



Chitra Insultec Pvt. Ltd.
Heat Protection & Waterproofing
202, Sarthak II, Near Swastik Cross Road, Navrangpura, Ahmedabad - 380009, Gujarat, India
Mrs. Supriya Mehta (Director)

Product Showcase
Send Inquiry Send SMS    Call Me Free Offline